Note: A more recent version of this product is available. This point dataset contains the major power stations in Australia including all those that feed into the electricity transmission network.

Covering an area of approximately 247 000km2, the Galilee Basin is a significant feature of central Queensland. Three main depocentres contain several hundred metres of Late Carboniferous to Middle Triassic sediments. Sedimentation in the Galilee Basin was dominated by fluvial to lacustrine depositional systems. This resulted in a sequence of sandstones, mudstones, siltstones, coals and minor tuff in what was a relatively shallow intracratonic basin with little topographic relief. Forty years or more of exploration in the Galilee Basin has failed to discover any economic accumulations of hydrocarbons, despite the presence of apparently fair to very good reservoirs and seals in both the Permian and Triassic sequence. Despite some relatively large distances (upwards of 500km) between sources and sinks, previous and ongoing work on the Galilee Basin suggests that it has potential to sequester a significant amount of Queensland's carbon dioxide emissions. Potential reservoirs include the Early Permian Aramac Coal Measures, the Late Permian Colinlea Sandstone and the Middle Triassic Clematis Sandstone. These are sealed by several intraformational and local seals as well as the regional Triassic Moolayember Formation. With few suitable structural traps and little faulting throughout the Galilee sequence, residual trapping within saline reservoir is the most likely mechanism for storing CO2. The current study is aimed at building a sound geological model of the basin through activities such as detailed mapping, well correlation, and reservoir and seal analysis leading to reservoir simulations to gain a better understanding of the basin.

A metadata report for the atmospheric monitoring station installed in Arcturus, south of Emerald in central Queensland. The station was installed for baseline atmospheric monitoring to contribute to emission modelling spanning 2010-2014. The station included compositional gas analysers, supporting meteorological sensors and an eddy covariance flux tower. The metadata covered in the report include: the major variables measured by each instrument, the data duration and frequency, data accuracy, calibration and corrections, the location the data is stored, and the primary contact for the data.

Hot Rocks in Australia - National Outlook Hill, A.J.1, Goldstein, B.A1 and Budd, A.R.2 goldstein.barry@saugov.sa.gov.au hill.tonyj@saugov.sa.gov.au Petroleum & Geothermal Group, PIRSA Level 6, 101 Grenfell St.Adelaide SA 50001 Anthony.Budd@ga.gov.au Onshore Energy & Minerals Division, Geoscience Australia, GPO Box 378 Canberra ACT 26012 Abstract: Evidence of climate change and knowledge of enormous hot rock resources are factors stimulating growth in geothermal energy research, including exploration, proof-of-concept appraisals, and development of demonstration pilot plant projects in Australia. In the six years since the grant of the first Geothermal Exploration Licence (GEL) in Australia, 16 companies have joined the hunt for renewable and emissions-free geothermal energy resources in 120 licence application areas covering ~ 67,000 km2 in Australia. The associated work programs correspond to an investment of $570 million, and that tally excludes deployment projects assumed in the Energy Supply Association of Australia's scenario for 6.8% (~ 5.5 GWe) of Australia's base-load power coming from geothermal resources by 2030. Australia's geothermal resources fall into two categories: hydrothermal (from relatively hot groundwater) and the hot fractured rock i.e. Enhanced Geothermal Systems (EGS). Large-scale base-load electricity generation in Australia is expected to come predominantly from Enhanced Geothermal systems. Geologic factors that determine the extent of EGS plays can be generalised as: - source rock availability, in the form of radiogenic, high heat-flow basement rocks (mostly granites); - low thermal-conductivity insulating rocks overlying the source rocks, to provide thermal traps; - the presence of permeable fabrics within insulating and basement rocks, that can be enhanced to create heat-exchange reservoirs; and - a practical depth-range, limited by drilling and completion technologies (defining a base) and necessary heat exchange efficiency (defining a top). A national EGS resource assessment and a road-map for the commercialisation of Australia's EGSs are expected to be published in 2008. The poster will provide a synopsis of investment frameworks and geothermal energy projects underway and planned in Australia.

Having techniques available for the accurate quantification of potential CO2 surface leaks from geological storage sites is critical for regulators, public assurance and for underpinning carbon pricing mechanisms. Currently, there are few options available that enable accurate CO2 quantification of potential leaks at the soil-atmosphere interface. Integrated soil flux measurements can be used to quantify CO2 emission rates from the soil and atmospheric techniques such as eddy covariance or Lagrangian stochastic modelling have been used with some success to quantify CO2 emissions into the atmosphere from simulated surface leaks. The error for all of these techniques for determining the emission rate is not less than 10%. A new technique to quantify CO2 emissions was trialled at the CO2CRC Ginninderra controlled release site in Canberra. The technique, termed atmospheric tomography, used an array of sampling sites and a Bayesian inversion technique to simultaneously solve for the location and magnitude of a simulated CO2 leak. The technique requires knowledge of concentration enhancement downwind of the source and the normalized, three-dimensional distribution (shape) of concentration in the dispersion plume. Continuous measurements of turbulent wind and temperature statistics were used to model the dispersion plume.

Deployment of Unmanned Aerial Vehicle during surface CO2 release experiments at the Ginninderra greenhouse gas controlled release facility H. Berko (CO2CRC, Geoscience Australia), F. Poppa (The Australian National University), U. Zimmer (The Australian National University) and A. Feitz (CO2CRC, Geoscience Australia) Lagrangian stochastic (LS) forward modelling of CO2 plumes from above-surface release experiments conducted at the GA-CO2CRC Ginninderra controlled release facility demonstrated that small surface leaks are likely to disperse rapidly and unlikely to be detected at heights greater 4 m; this was verified using a rotorcraft to map out the plume. The CO2 sensing rotorcraft unmanned aerial vehicle (RUAV) developed at the Australian National University, Canberra, is equipped with a CO2 sensor, a GPS, lidar and a communication module. It was developed to detect and locate CO2 gas leaks; and estimate CO2 concentration at the emission source. The choice of a rotor-craft UAV allows slower flight speeds compared to speeds of a fixed-wing UAV; and the electric powered motor enables flight times of 12 min. In experiments conducted at the Ginninderra controlled release facility, gaseous CO2 (100 kg per day) was released from a small diffuse source located in the middle of the paddock, and the RUAV was flown repeatedly over the CO2 source at a few meters height. Meteorological parameters measured continuously at the site at the time of the flight were input in the LS model. Mapped out horizontal and vertical CO2 concentrations established the need to be close to the ground in order to detect CO2 leakage using aerial techniques. Using the rotorcraft as a mobile sensor could be an expedient mechanism to detect plumes over large areas, and would be important for early detection of CO2 leaks arising from CCS activities.

Geoscience Australia and CO2CRC have constructed a greenhouse gas controlled release reference facility to simulate surface emissions of CO2 (and other GHG gases) from an underground slotted horizontal well into the atmosphere under controlled conditions. The facility is located in a paddock maintained by CSIRO Plant and Industry at Ginninderra, ACT. The design of the facility is modelled on the ZERT controlled release facility in Montana, which conducts experiments to develop capabilities and test techniques for detecting and monitoring CO2 leakage. The first phase of the installation is complete and has supported an above ground, point source, release experiment, utilising a liquid CO2 storage vessel (2.5 tonnes) with a vaporiser, mass flow controller unit with a capacity for 6 individual metered gas outlet streams, equipment shed and a gas cylinder cage. Phase 2 involved the installation of a shallow (2m depth) underground 120m horizontally drilled slotted well, in June 2011, intended to model a line source of CO2 leakage from a storage site. This presentation will detail the various activities involved in designing and installing the horizontal well, and designing a packer system to partition the well into six CO2 injection chambers. A trenchless drilling technique used for installing the slotted HDPE pipe into the bore hole will be described. The choice of well orientation based upon the effects of various factors such as topography, wind direction and ground water depth, will be discussed. It is envisaged that the facility will be ready for conducting sub-surface controlled release experiments during spring 2011.

Quantification of leakage into the atmosphere from geologically stored CO2 is achievable by means of atmospheric monitoring techniques if the position of the leak can be located and the perturbation above the background concentration is sufficiently large for discrimination. Geoscience Australia and the CO2CRC have recently constructed a site in northern Canberra for the controlled release of greenhouse gases. This facility enables the simulation of leak events and provides an opportunity to investigate techniques for the detection and quantification of emissions of CO2 (and other greenhouse gases) into the atmosphere under controlled conditions. The facility is modelled on the ZERT controlled release facility in Montana. The first phase of the installation is complete and has supported an above ground, point source, release experiment (e.g. simulating leakage from a compromised well). Phase 2 involves the installation of a shallow underground horizontal well for line source CO2 release experiments and this will be installed during the first half of 2011. A release experiment was conducted at the site to explore the application of a technique, termed atmospheric tomography, to simultaneously determine the location and emission rate of a leak when both are unknown. The technique was applied to the release of two gas species, N2O and CO2, with continuous sampling of atmospheric trace gas concentrations from 8 locations 20m distant from a central release point and measurement of atmospheric turbulence and dispersive conditions. The release rate was 1.10 ± 0.02 g min-1 for N2O and 58.5 ± 0.4 g min-1 for CO2 (equivalent to 30.7 ± 0.2 tonnes CO2 yr-1). Localisation using both release species occurred within 0.5 m (2% error) of the known location. Determination of emission rate was possible to within 7% for CO2 and 5% for N2O.

A shallow vertical CO2 injection test was conducted over a 21 day period at the Ginninderra Controlled Release Facility in May 2011. The objective of this test was to determine the extent of lateral CO2 dispersion, breakthrough times and permeability of the soil present at the Ginninderra site. The facility is located in Canberra on the CSIRO agricultural Ginninderra Experiment Station. A 2.15m deep, 15cm stainless steel screened, soil gas sampling well was installed at the site and this was used as the CO2 injection well. The CO2 flow rate was 1.6 L/min (STP). CO2 soil effluxes (respiration and seepage) were measured continuously using a LICOR LI-8100A Automated Soil CO2 Flux System equipped with 5 accumulation chambers spaced 1m apart in a radial pattern from the injection well. These measurements were supplemented with CO2 flux spot measurements using a WestSystems portable fluxmeter. Breakthrough at 1m from the injection point occurred within 6 hrs of injection, 32hrs at 2m and after almost 5 days at 3m. The average steady state CO2 efflux was 85 ?mol/m2/s at 1m, 15 ?mol/m2/s at 2m and 5.0 ?mol/m2/s at 3m. The average background CO2 soil respiration efflux was 1.1 - 0.6 ?mol/m2/s. Under windy conditions, higher soil CO2 efflux could be expected due to pressure pumping but this is contrary to the observed results. Prolonged windy periods led to a reduction in the CO2 efflux, up to 30% lower than the typical steady state value.

A short animation of an atmospheric simulation of methane emissions from a coal mine (produced using TAPM) compared to actual methane concentrations detected by the Atmospheric Monitoring Station, Arcturus in Central Queensland. It illustrates the effectiveness of both the detection and simulation techniques in the monitoring of atmospheric methane emissions. The animation shows a moving trace of both the simulated and actual recorded emissions data, along with windspeed and direction indicators. Some data provided by CSIRO Marine and Atmospheric Research.